Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant here. Do not following these rules will lead to permanent exclusion from this website: Read the forum rules.
See here for 3D printing related threads: http://www.xsimulator.net/community/forums/3d-printing.158/
3D printed VR HMD mount: https://www.xsimulator.net/community/threads/hmd-chair-mount-holder.13123/
Quick Mounts For HTC Vive Lighthouses by @Zed: https://www.xsimulator.net/community/threads/quick-mounts-for-htc-vive-lighthouses.11941/
3D printed mount by @CBC_North: https://www.xsimulator.net/communit...mover-with-diy-peripherals.12178/#post-163742
3D printed pot mount by @digitalmonk: https://www.xsimulator.net/community/threads/3dof-seat-mover.11103/#post-143599
DIY linear actuator parts by @baykah: https://www.xsimulator.net/community/threads/6dof-sim-linear-actuator-diy-sabertooth-arduino.9392/
Power Entry Module Housing by @Zed: https://www.xsimulator.net/community/threads/power-entry-module-housing.10584/#post-137108
3D printed H-Shifter + shifter & buttons for race wheel: https://www.xsimulator.net/communit...shifter-shifter-buttons-for-race-wheel.10379/
JRK underside board cooler mount by @Zed: https://www.xsimulator.net/community/threads/jrk-12v12-overheating.10327/#post-133739
Touch controller mount by @Azel for use with motion cancellation: https://www.xsimulator.net/communit...culus-touch-holder-bracket.10355/#post-133717
Pot connection coupling by @Andrew M: https://www.xsimulator.net/communit...shield-3d-printed-elements.10325/#post-134013
Wiper motor post mounts by @insanegr: https://www.xsimulator.net/communit...ts-sim-related-prints.9057/page-2#post-123997
Vive Tracker mount: https://www.xsimulator.net/communit...-vive-and-vive-tracker-a-tracker-mount.10346/
Pot mount, connector and sundry parts by @Azel: https://www.xsimulator.net/community/threads/diy-2dof-made-mostly-of-scrapyard-parts-and-top-quality-electronics™.10326/
Hall sensor mount, mag mount and U joint spacer by @Zed: https://www.xsimulator.net/community/threads/starting-my-own-2dof-rig.10235/page-3#post-132900
And Amp gauge box: https://www.xsimulator.net/community/threads/starting-my-own-2dof-rig.10235/page-3#post-132988
Dsub 15 for OSW builds, submitted by @Nick Moxley: https://www.xsimulator.net/community/threads/dsub-15-for-osw-builds.9385/
Honeycomb fan air straighteners by @Avenga76: https://www.xsimulator.net/community/members/avenga76.10691/
Modified snap on honeycomb fan air straighteners by @HoiHman: https://www.xsimulator.net/communit...ermoto-and-arduinouno.6876/page-9#post-114138
Moto Monster ventilated box by @Avenga76: https://www.xsimulator.net/communit...ermoto-and-arduinouno.6876/page-7#post-113677
Moto Monster ventilated box with internal fan by @Avenga76: https://www.xsimulator.net/communit...ermoto-and-arduinouno.6876/page-9#post-114400
Combined 3D printed Arduino case with dual Motor Monster wings by @stevemontuno : http://www.thingiverse.com/thing:1510217/#files
Moto Monster slide on 80mm fan holder by @HoiHman: https://www.xsimulator.net/communit...rmoto-and-arduinouno.6876/page-10#post-114424
3D printed file for custom All in one 3 X PSU and JRK Cooler Master Elite Case Mod: http://www.xsimulator.net/community/faq/all-in-one-3-x-psu-and-jrk-cooler-master-elite-case-mod.199/
Download 3D files by @rundmg here: http://www.xsimulator.net/community...f-simulator-conversion.5914/page-4#post-89608
3D quick release steering wheel hub by @RacingMat: http://www.xsimulator.net/community/threads/3d-printed-quick-release.6360/#post-70710
If you like your creature comforts then here is a cup holder and bracket by @HoiHman: https://www.xsimulator.net/community/threads/drinking-cup-cupholder.9103/
Below is a summary of a diverse range of 3D Printed objects made available by @Ville Pesonen in one package: http://www.xsimulator.net/community/threads/2dof-motion-simulator-build.6196/page-7#post-88219
It's basically a mount for a nut that you can screw to somewhere.
Never managed to print this...
I used this to keep 2 diodes in place to stop reverse current reaching the PSU's
Gas spring mount:
Part to hold gas spring in place. It clamps around 30x30mm tube
You can screw a cheap chinese H bridge to this
You can screw monster moto shield to this
Coulus Camera holder:
This part slips inside 30x30mm tube and has a hole in the middle for a camera mount screw.
just a tube that goes over the potentiometers shaft and can be glued to the shaft of a motor
I used this to mount potentiometers next to the motor. the holes are in line with the motor mount holes. I can't remember the model of the motor that I have...you can find it somewhere in this build thread.
Never used this, but it was meant to hold the psus in place.
little part to hold a power switch in place