1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

Recent Activity

Activity stream for all registered members at Motion Simulator Community.

  1. MaxPower replied to the thread Linear actuator using ClearPath Integrated Servo System @ 72V DC.

    I didn't mean to consider going from 550mm stroke to 750mm stroke. I mean perhaps when I order the first ballscrew to refine the design...

    May 21, 2024 at 16:14

  2. Claudemir liked RacingMat's post in the thread [WIP] DIY active pedal by Tristian Fenwick.

    Hi there :) Here is a promissing project for DIY active pedals: https://github.com/tjfenwick/DIY-Sim-Racing-Active-Pedal by Tristian...

    May 21, 2024 at 16:06

  3. Marco Annunziata replied to the thread FlyPT Mover.

    Pedro, that's exactly what I needed. Thank you very much for your job!

    May 21, 2024 at 15:56

  4. Marco Annunziata rated pmvcda's post Friendly in the thread FlyPT Mover.

    [ATTACH] Look what I have for the new release. It's not fully functional yet (95%, still missing a small part of he code) You define a...

    upload_2024-5-21_12-37-4.png May 21, 2024 at 15:53

  5. PeterW attached a file to the thread FlyPT Mover.

    Hello Hello FlyPT! So great to see your continous hard work and improvements on mover!!! Thank you so much!! When I had a look to...

    upload_2024-5-21_15-28-29.png upload_2024-5-21_15-31-35.png May 21, 2024 at 15:48

  6. Raysinred replied to the thread Question Beginner Looking for 3 DOF Arduino Code with Sabertooth Controller.

    Thank you noorbeast, One more question. Is the SMC3 code just for testing and setting the parameters and ports? What is the difference...

    May 21, 2024 at 14:26

  7. Klaus Schmidinger liked pmvcda's post in the thread FlyPT Mover.

    [ATTACH] Look what I have for the new release. It's not fully functional yet (95%, still missing a small part of he code) You define a...

    upload_2024-5-21_12-37-4.png May 21, 2024 at 14:22

  8. pmvcda attached a file to the thread FlyPT Mover.

    [ATTACH] Look what I have for the new release. It's not fully functional yet (95%, still missing a small part of he code) You define a...

    upload_2024-5-21_12-37-4.png May 21, 2024 at 13:40

  9. Richard Eaton replied to the thread Question Dc motor driver proplems.

    Hi, I'm about to swap my IBT2 out for something different, were these any good, obviously a lot more expensive, did you sort the wiring out?

    May 21, 2024 at 13:02

  10. Richard Eaton replied to the thread Motor Cutting Out.

    Many thanks , appreciate the advice, I don't believe it is an issue with the power as the 2 supplies I have are more than adequate for...

    May 21, 2024 at 12:54

  11. deeph46 replied to the thread Motor Cutting Out.

    Just a info, from my experienced and have similar problem with what you are describe. On my rig it was the power not enough draw the...

    May 21, 2024 at 12:37

  12. Gadget999 replied to the thread Linear actuator using ClearPath Integrated Servo System @ 72V DC.

    does it come with drivers - are they the correct type ?

    May 21, 2024 at 11:39

  13. Dirty replied to the thread Linear actuator using ClearPath Integrated Servo System @ 72V DC.

    That is indeed a good price for 6 x 1.2KW servos. Maybe the 110mm form factor is in less demand than the 80mm form factor? It is...

    May 21, 2024 at 11:03

  14. simnolimits03 replied to the thread Question iRacing simtools patching invalid and ACC doesnt appear on my Game Manager.

    Hi! Thank you for the response I'm using the SimTools V2.6 as of now. In iRacing, I'm patching the whole iRacing folder. Is that...

    May 21, 2024 at 09:17

  15. simnolimits03 liked noorbeast's post in the thread Question iRacing simtools patching invalid and ACC doesnt appear on my Game Manager.

    First can I note it is now clear there are iRacing plugin related issues post the last iRacing update, so please see and monitor the...

    May 21, 2024 at 09:16
Show older items
Loading...