1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

Pot Placement One Sided Wiper

Discussion in 'DIY Motion Simulator Building Q&A / FAQ' started by dieser, Mar 14, 2020.

  1. dieser

    dieser Member

    Joined:
    Jan 20, 2020
    Messages:
    54
    Balance:
    372Coins
    Ratings:
    +12 / 0 / -0
    Hey guys!
    I need your knowledge once again. ;)

    I‘m in my first steps to build a simple 2 Dof Seatmover with 12v wipers.

    My Wipers are RIDEX 295w0010

    They‘re already coming with a bold shaft on the lever side.

    Any ideas where i can place a pot here???

    I thought about turning the backplate off and gluing a bolt on it or something...

    or is it better to extend the motor shaft and connect it to the pot?
    i concerned this, because there is no lever full turn possible then anymore :/


    i really need some advise.

    thank you guys, great community here!
    :)

    3A498A34-E7EE-40CC-9FE3-59B515F7EBF7.jpeg

    2137A41B-48FD-44BD-9393-409395B62879.jpeg
    Last edited: Mar 14, 2020
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,460
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    144,596Coins
    Ratings:
    +10,741 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    • Like Like x 1
  3. Map63Vette

    Map63Vette Member

    Joined:
    May 19, 2016
    Messages:
    127
    Occupation:
    Mechanical Engineer
    Location:
    Lawrence, KS
    Balance:
    430Coins
    Ratings:
    +31 / 0 / -0
    I set mine up with a 3D printed "socket" that slips over the nut. I got the potentiometers with a flat shaft so I could just slide them into the printed piece vs needing a set screw or something like that on a round shaft.

    Coupler 2.jpg Shaft Coupler.jpg
    • Like Like x 1
  4. dieser

    dieser Member

    Joined:
    Jan 20, 2020
    Messages:
    54
    Balance:
    372Coins
    Ratings:
    +12 / 0 / -0
    ah, i see, great idea!

    but there is still the problem with no possible turnaround, isn‘t it?
  5. Map63Vette

    Map63Vette Member

    Joined:
    May 19, 2016
    Messages:
    127
    Occupation:
    Mechanical Engineer
    Location:
    Lawrence, KS
    Balance:
    430Coins
    Ratings:
    +31 / 0 / -0
    Yes, I suppose it does limit the rotation some, though I was only planning to use about 45 degrees each way. Is there are reason you are looking for more rotation than that? You lose the mechanical advantage of the lever as the angle increases, so you need a lot of torque if you want to go more than 45 degrees. Most seat mover designs don't use more than that from what I've seen here at least.
  6. dieser

    dieser Member

    Joined:
    Jan 20, 2020
    Messages:
    54
    Balance:
    372Coins
    Ratings:
    +12 / 0 / -0
    not a real reason. i read somewhere here that the possibility of a free rotation prevents me of damaging something.
  7. Map63Vette

    Map63Vette Member

    Joined:
    May 19, 2016
    Messages:
    127
    Occupation:
    Mechanical Engineer
    Location:
    Lawrence, KS
    Balance:
    430Coins
    Ratings:
    +31 / 0 / -0
    Ah, that's fair. I could see having settings wrong when you are first setting things up that could cause your motors to turn more angle than you were expecting. I'll have to watch for that myself if I ever get around to building my frame mover.
  8. dieser

    dieser Member

    Joined:
    Jan 20, 2020
    Messages:
    54
    Balance:
    372Coins
    Ratings:
    +12 / 0 / -0
    hey there!
    I just wanted to share how I solved my problem in the starting post.
    maybe there some other members who are asking the same i did.

    I decided to extend the shaft of my one-sided wiper motor, but to get the possibility of a full turnaround I placed the the pot-gears behind the lever. I used the gear of simukit, however you can use any other...

    IMG_4656 Kopie.jpg IMG_4657 Kopie.jpg

    hope this will help someone! ;)
    • Like Like x 1