1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

Showroom New 6 DOF sim with ultra advanced controller

Discussion in 'DIY Motion Simulator Projects' started by agroum, Jun 29, 2019.

  1. agroum

    agroum My solo 11 years ago

    Joined:
    Jun 24, 2017
    Messages:
    15
    Occupation:
    Mechatronics engineer / part time aero master
    Location:
    Canada
    Balance:
    154Coins
    Ratings:
    +20 / 0 / -0
    My Motion Simulator:
    Motion platform, 6DOF
    Hello everyone,

    2 years ago, I presented for the first time a DIY 6DOF working concept. 2 weeks ago, I finished the 2.0 version of that project. This new version has been improved significantly in terms of motion. I’m extremely proud to share my project with all of you.

    Take a look! I’ll be posting videos soon, stay tuned.

    Cheers,

    Michael

    20190613_231456.jpg
    • Like Like x 8
    Last edited: Jun 29, 2019
  2. agroum

    agroum My solo 11 years ago

    Joined:
    Jun 24, 2017
    Messages:
    15
    Occupation:
    Mechatronics engineer / part time aero master
    Location:
    Canada
    Balance:
    154Coins
    Ratings:
    +20 / 0 / -0
    My Motion Simulator:
    Motion platform, 6DOF
  3. Thanos

    Thanos Building the Future one AC Servo at a time... or 6

    Joined:
    Jul 6, 2017
    Messages:
    1,342
    Occupation:
    Electronics Engineer
    Location:
    United States
    Balance:
    2,672Coins
    Ratings:
    +1,043 / 9 / -0
    My Motion Simulator:
    AC motor, Motion platform, 4DOF, 6DOF
    Interesting. Are these DC motors?
  4. agroum

    agroum My solo 11 years ago

    Joined:
    Jun 24, 2017
    Messages:
    15
    Occupation:
    Mechatronics engineer / part time aero master
    Location:
    Canada
    Balance:
    154Coins
    Ratings:
    +20 / 0 / -0
    My Motion Simulator:
    Motion platform, 6DOF
    Yes 12V, I use 3 roboclaw drivers, but all the regulation is made in an other board.
    Simtools is only used to send the raw data to the controller.

    It allows to make figure like a circle or an 8 in a plan.

    The time between the set point and the position value is between 30 and 60ms with a maximum error of 1/3 of mm when there is a peak and an average about 1/5 of mm.
    Last edited: Jun 29, 2019
  5. BM114

    BM114 New Member

    Joined:
    Jun 7, 2019
    Messages:
    26
    Balance:
    236Coins
    Ratings:
    +7 / 1 / -0