1. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Download Package Now!
  2. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  3. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant here. Do not following these rules will lead to permanent exclusion from this website: Read the forum rules.
Plugin Downloads Zero spam policy Forum Rules

DIY Motion Simulator Building Q&A / FAQ

Generic questions and suggestions about DIY motion simulator building.

Page 1 of 10

Filters:

Prefix:
Question x
Remove All Filters:
x
Sort By:
Title Start Date
Replies Views
Last Message ↓
  1. Horker

    Question Électrical issue with my controler

    Horker, Jun 18, 2019 at 22:18
    Replies:
    0
    Views:
    56
    Horker
    Jun 18, 2019 at 22:18
  2. jaymac7

    Question X-post: is this a SCN5 failure or software issue?

    jaymac7, Jun 16, 2019
    Replies:
    0
    Views:
    51
    jaymac7
    Jun 16, 2019
  3. Thomas Luzat

    Question Ball screw linear actuator dimensioning and platform stopping

    Thomas Luzat, Mar 26, 2019
    Replies:
    2
    Views:
    216
    Thanos
    Jun 14, 2019
  4. Mike Stuart

    Question 180 degree hall sensors with SMC3 and sabertooth.

    Mike Stuart, Jun 12, 2019
    Replies:
    4
    Views:
    101
    BlazinH
    Jun 13, 2019
  5. Jstone

    Question JRK not showing in utility config

    Jstone, Jun 5, 2019
    Replies:
    4
    Views:
    72
    Jstone
    Jun 7, 2019
  6. Jakob Carron

    Question Smc3 trouble

    Jakob Carron, Jun 3, 2019
    Replies:
    3
    Views:
    108
    noorbeast
    Jun 5, 2019
  7. Cripple

    Question Aluminium Extrusion - how thick?

    Cripple, May 15, 2019
    Replies:
    3
    Views:
    241
    dododge
    Jun 3, 2019
  8. Alex st-louis

    Question 2 DOF best hardware?

    Alex st-louis, May 23, 2019
    Replies:
    10
    Views:
    291
    Alex st-louis
    May 23, 2019
  9. brocessor

    Question Simtools Serial Port (Test Output) Not Working

    brocessor, May 22, 2019
    Replies:
    2
    Views:
    101
    ghidossi
    May 22, 2019
  10. wp8051

    Question About the installation of the universal joint

    wp8051, Apr 16, 2019
    Replies:
    12
    Views:
    330
    wp8051
    May 16, 2019
  11. hestenet

    Question Low-noise actuators? (SCN6 vs SFX-100 for example?)

    hestenet, May 12, 2019
    Replies:
    2
    Views:
    242
    Thanos
    May 13, 2019
  12. docsimo85

    Question From X-sim to Simtool

    docsimo85, May 9, 2019
    Replies:
    2
    Views:
    127
    docsimo85
    May 9, 2019
  13. Arazok

    Question Gearchange - too much movement

    Arazok, May 8, 2019
    Replies:
    9
    Views:
    206
    noorbeast
    May 9, 2019
  14. bixler13

    Question pgsaw lever mounting

    bixler13, Mar 26, 2019
    Replies:
    7
    Views:
    353
    yellofella
    Apr 22, 2019
  15. Arazok

    Question Too much lash on motor shaft ?

    Arazok, Apr 9, 2019
    Replies:
    6
    Views:
    249
    yellofella
    Apr 22, 2019
  16. Garrett Jones

    Question U Joint

    Garrett Jones, Apr 17, 2019
    Replies:
    4
    Views:
    192
    427Cobra
    Apr 22, 2019
  17. Trigen

    Question Saber 2x32 Voltage clamp, automatic or 12v?

    Trigen, Apr 20, 2019
    Replies:
    5
    Views:
    167
    Trigen
    Apr 21, 2019
  18. FoxHound.92

    Question On/ Off Switch recommendations

    FoxHound.92, Feb 13, 2019
    Replies:
    18
    Views:
    455
    CBC_North
    Apr 15, 2019
  19. stashy

    Question SCN 6 40 OR 60

    stashy, Apr 12, 2019
    Replies:
    0
    Views:
    139
    stashy
    Apr 12, 2019
  20. Jstone

    Question Choosing PSU and Motors for Ard/MM

    Jstone, Apr 9, 2019
    Replies:
    7
    Views:
    212
    noorbeast
    Apr 11, 2019
Showing threads 1 to 20 of 190

Thread Display Options

Loading...
Page 1 of 10