Are YOU a NEW MEMBER? Introduce HERE!

Hi ~ I'm on 360 web pages to send message. Directly translated into English, it is estimated that many friends will look not to come out. No way, who let my English is not good. Ha ha ~ G force in high school like the car chair. Lucky enough to enter this mistake professional BBS, now study hard to make a four axis racing chair ~ now on web page translation machine in learning very hard, also please your comments. Thank you very much!

Hello All,
Justin here from Melbourne, Australia.

I am so very fully on the VR hype train, my Rift is on the way in the first delivery batch.
Im over forty and its been a while since Ive been excited with pc gaming again.
Its even better that my son is 11 now and gaming with him is far more enjoyable with him.

So now the Rift is on the way, my mind is turning towards a sim platform to maximize the VR experience.
Ive got a lot more reading to do in the forums before I decide what machine to build.

Congratulations to you all on a vibrant community,
Thank you to the many contributors.

Cheers

Part 1
Hi, my Name is Gerd
I´m a 59 year old flight Enthusiast ,
So, start with sailplanes and following by flight Simulation since 30 years
I own one of the first rock n rides and last week after a long time I reactivated the chair connected by a Serial cable on Com 2 to my Win 7 64 bit and prepar 3 d V3
With the original Software "Motion plus" for FX I got the chair to move as in the old days. But with the same rough behaviour, sometimes.
But i also like to get my x-plane 10 to work with the rock n ride and I got no successs. All important Settings were done in the x-plane like dataRefOut and IP for Data Output 127.0.0.1 at 4123 but got no success.
Than I checked the web and found your sim tool engine and Manager. So I decided to invest 39 € to get a nice smooth Connection to my rock n ride chair.

Part II will follow

new member with rock n ride
Part II

I installed your program and followed the manual. I installed the plug ins and started the games X-plane and later P3D. All worked fine in the simulator and the data were send to the sim Tools game engine. This i checked by the game engine sim tool Tuning Center and saw the different Game Data Input figures.
BUT , I did not get my chair to move, the valves and ventiles did not react.
So I Need some help for this last step to enjoy your program
I simply did not know what i need to insert in the Axis Assign
What did i insert for:
Axis 1 DOF 1 DOF 2
Axis 2 DOF 1 DOF 2
and further??
(under load a preset i see an Option for Rock n ride --> should i take this??

Part III

For the Interface Settings i also did not find relevant answers in the Forum of the xsimulator web side
So I tried several Setups for Serial with Com 2, 9600 bit per second, 8 Data Bits, Parity None, Stop bits 1
But i have no Idea for the right figures for:
- Output Bit Range
- Startup Output
- Interface Output
- Shutdown Output


PS It was tricky to get the post through the system

Thank´s in advance!
Gerd

@Dello please open a new thread in the specific forum, here we welcome new members and do not support in any case. Thank you.

Hi all, I'm an Frex SCM user who just completed the conversion to X-Sim thanks to this forum and in process of refurbishing my old 2009 rig to current standards. Look forward to learning a lot here!

Hello everyone! I am enthusiast from Cold Russia, who loves bikes, and enginering anything. Im very new to the motion simulators, but hope can build good cheap motorcycle simulator with 3DOF (2 at least)

Already create the thread on diy projects forum, who intersted - welcome

Thank you all for greatfull website like this.

Future of enginering in community i think)

Hello, my name is Matteo, i'm from Italy. I like cars simulator and i try to create one.

See for a few days with translation machines along with basic English BBS, a general train of thought. Ready to make a 4 dof, not directly do 4 dof way, ha ha ~ hope for BBS friends help.
Thank you sincerely.
Use translator to translate Chinese into English directly, how many there will be a mistake, please forgive me.

I am a new member from thailand.
I hope i will be able to accomplish that with the help of some experienced members.

Hello
I am new to the forum, I started making my simulator, a 2 DOF.
Manufacturing approach to its end so I should start the party software soon.
I'm sorry for my English, but using google translation ...

Hi everyone, my first post here. Just wanted to say what an awesome forum by awesome ppl. There is a wealth of information here which is fun to go through.

I just ordered an Arduino kit with which I wana try out mini 2DOF/6DOF with sim tools to see how it will work.

Wish me luck and I am sure I will be asking for help here