SimTools v3 Public Beta

https://youtube.com/shorts/FXoB0sNpP_U?si=CxJp3Hm_XaO7idYV. It only sounds like that when I turn the steering wheel, other than that nothing, rpm, bumps

Rpm number I tried several settings, but I couldn't get it to work correctly at all, I also tried assetto corsa, grid, grid legends but with these it crashes and simtools closes

So I've been using v1.2 for a long time. But wanted to upgrade to v3. However after downloading the demo of both v3 and live4speed to test with, as well as all required plugins. I have run into an issue.
I use the server interface and copied the setup from my v1.2
Then set up just a pitch dof with only 25 % force and 25 boundary to play it safe.
With the power off I downloaded the slider plugin to check the virtual axis. When it looked good I powered on the seat. Once I hit the test button my seat goes all the way forward and tries to pass my physical safety stops.
I exited v3 and tried the seat again using v1.2 to rule a seat problem out however it operates as it should so that leads me to believe I am doing something wrong or the program has a fundental difference in the interface setting.

What might it be?

They are the same. Is my problem that I didn't put an "a" behind the axis?

Hi Yobuddy,

Just wondering, any update on the RC-Rider?

Thanks

Hello so im getting an error saying

DEBUG error!
Program: J:\Simtools3\wow64ext.dll
Module:J:\Simtools3\wow64ext.dll
File:

Runtime check failure #3 - the variable 'basicaddrrss64' is being used without being initialized l.

Appolgies for sounding a bit dense
Cannot get this to work

Simtools v3. New install new PC etc
All ok at Simtools v3 startup scn6 actuators move etc & now fine under testing

Simtools v3 downloaded the msfs2020 within Simtools v3 plugins selection

The mafs2029 plug in clicked twice does start mafs2020 but zero motion

I’ve assigned basic axis pitch roll now turned up but zero movement

msfs2020 does run motion when I try using sim commander software so it does output but sim commander not great for flight sims

any ideas of how to get it to work ?

Has anyone got msfs2020 to work with Simtools 3 ????

Working now thanks

but cannot get the msfs2020 plug in to work

Simtools 3 & installed msfs2020 plug in through the Simtools 3 interface

the sadness is sapping my Will

just tried it with ams2 , simtools not receiving input from the games

all the motion works when i test actutors and adjust park postions etc

yes i put in some pitch roll etc into the first 2 axis, the ones that are working and simetools 3 activate at start up
simetools 3 successfully starts the game from pressing the plugin twice etc

is there something I've missed out???????????????????????????????????????????????????????????????????

Here

massive thanks for reply

interface one ( com 6 ) axis 1a
Interface two (com 5 ) axis 2a

bott work nicely at startup
+on the test mode they move no probs

zero movement in game
Simtools 3 boots up/starts the game no problem , tested with msfs2020 & ams2
Both completely dead motion

frustrating
Any suggestions appreciated

thanks yobuddy

nope none of things worked
I tried output of 1 on each axis then 2 , 3 , 4 , 10

the min max I fiddled and put different figures in

nothing shows in those “input” boxes above isn’t that a life feed from the sim ?
I pressed capture too but nothing showed in those boxes , all whilst msfs2020 was running with a plane flying

zero movement

there’s nothing coming from each sim

I know my setup works with everything including ams2 & mafs2020 using sim commander software so I know not a hardware or connection to pc issue

Is my somehow blocking the feed from sim to Simtools 3 ?

It’s a new pc with clean install of windows 10 & working with everything else great , VR etc

is simtools V3 not working because I’m using windows 10 maybe ? ???????

PS i have one drive switched off if that makes any difference

is there any patching I need to do in the game(s) so simtools v3 supplies physical motion ?