1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

Bourns 3590s 10 Turn Potentiometer

Discussion in 'DIY Motion Simulator Building Q&A / FAQ' started by getti, Mar 7, 2019.

  1. getti

    getti Currently building my first 2dof seat mover...

    Joined:
    Oct 27, 2012
    Messages:
    124
    Location:
    Canada
    Balance:
    45Coins
    Ratings:
    +45 / 1 / -0
    My Motion Simulator:
    2DOF
    I'm upgrading to Bourns 10 turn 10k. Is there anything special I need to do, software wise or other?
    About to start soldering.

    Arduino SMC3

    Thanks
    [​IMG]
  2. SilentChill

    SilentChill Problem Maker

    Joined:
    Jul 19, 2014
    Messages:
    2,619
    Occupation:
    Railway Maintenance
    Location:
    Morecambe, Lancashire, England
    Balance:
    20,395Coins
    Ratings:
    +3,480 / 34 / -0
    My Motion Simulator:
    DC motor, Arduino, Motion platform, 6DOF
    I wouldn't use them they are terrible, they lasted about a week, if that on my rig. 10 turn hall effect pot will be what I may use next however they are a little expensive
    Last edited: Mar 7, 2019
  3. SilentChill

    SilentChill Problem Maker

    Joined:
    Jul 19, 2014
    Messages:
    2,619
    Occupation:
    Railway Maintenance
    Location:
    Morecambe, Lancashire, England
    Balance:
    20,395Coins
    Ratings:
    +3,480 / 34 / -0
    My Motion Simulator:
    DC motor, Arduino, Motion platform, 6DOF
    Oh I see your on 2DOF with a worm gear ? you only need a 180 or 360 degree pot and I would highly recommend using the BT Tech Hall effect they are by far better choice
  4. getti

    getti Currently building my first 2dof seat mover...

    Joined:
    Oct 27, 2012
    Messages:
    124
    Location:
    Canada
    Balance:
    45Coins
    Ratings:
    +45 / 1 / -0
    My Motion Simulator:
    2DOF
    Oh ok, I wasn't expecting that. They look pretty good to me. Anyhow I already installed one so I think I'll just give it a go and see how they work. Is there anything I need to do inside simtools or SMC3 code?
  5. getti

    getti Currently building my first 2dof seat mover...

    Joined:
    Oct 27, 2012
    Messages:
    124
    Location:
    Canada
    Balance:
    45Coins
    Ratings:
    +45 / 1 / -0
    My Motion Simulator:
    2DOF
    Yes it's 3dof worm drive. The pots I've been using are in the picture on the right, cheap 10k 1 turn linear. I ordered these bourns not because they're 10 turn but because I'm hoping they're smoother, less jitter and last longer hopefully.