1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

Question What is the easiest way to move to a new PC

Discussion in 'SimTools DIY Version' started by Alexander Asner, Mar 7, 2019.

  1. Alexander Asner

    Alexander Asner New Member

    Joined:
    Jul 3, 2018
    Messages:
    22
    Balance:
    271Coins
    Ratings:
    +3 / 0 / -0
    My Motion Simulator:
    3DOF, SCN5, SCN6
    Hi,

    I am planning to buy a new PC shortly. In order to move my motion setup to the new machine, what is the easiest way? What can I copy over to the new installation, and what parts of the setup would I have to repeat manually.

    Any help is much appreciated.

    -Alex
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,461
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    144,602Coins
    Ratings:
    +10,741 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
  3. Alexander Asner

    Alexander Asner New Member

    Joined:
    Jul 3, 2018
    Messages:
    22
    Balance:
    271Coins
    Ratings:
    +3 / 0 / -0
    My Motion Simulator:
    3DOF, SCN5, SCN6
    Thank you. I suppose I would have to set up the assignments from scratch though, or is there some kind of ID for the actuators that is stored in the settings?
  4. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,461
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    144,602Coins
    Ratings:
    +10,741 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    The backup will store all current Interface, Axis Assignment and Game Manager profiles.
  5. Alexander Asner

    Alexander Asner New Member

    Joined:
    Jul 3, 2018
    Messages:
    22
    Balance:
    271Coins
    Ratings:
    +3 / 0 / -0
    My Motion Simulator:
    3DOF, SCN5, SCN6
    Ok. That sounds fantastic. I'll keep my fingers crossed.
  6. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,461
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    144,602Coins
    Ratings:
    +10,741 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    Depending on your hardware you may need to check the Interface Settings, as a different port could be allocated. The rest should be fine.

    You also have a limited number of SimTools registrations, so just go ahead and re-register your SimTools install when you do it.