1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

ERGUN's 4DOF

Discussion in 'Commercial Simulators and Peripherie' started by ERGUN, Jan 8, 2019.

  1. ERGUN

    ERGUN New Member

    Joined:
    Sep 3, 2018
    Messages:
    6
    Balance:
    - 25Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    3DOF, DC motor, Arduino
    Hi, I am new to forum. I am developping a 4dof simulator using arduino and BLDC motors. I need help on YAW axis. Other axises are ok. I am testing my sim with LFS. I can get values from simtools and send them to motor using arduino with no problems. But when I am spinning with car in LFS, upto 360 degree rotation simtools sends me values between 0 t0 255 as binary value. 127 binary value is center of yaw axis. 0 t0 127 is left up to 180 degre and 128 to 255 is 180 degree to the right. But when I spin more than 360 degrees, simtools sends me zero (0) binary value and motor turns 360 degree to reverse direction suddenly. My yaw is limited to 360 degree, so if I do spinning more than 360 degree continiously, my sim returns startup position and starting rotate again.

    My english is not fluent, so I hope I can tell the problem. Any help is required.

    Thanks.
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,463
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    144,614Coins
    Ratings:
    +10,741 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    As of the 2.3 SimTools update you can specify linear or rotational outputs plus a new anti rollover filter was also added.

    Can you please post a picture and other details of your design.
  3. ERGUN

    ERGUN New Member

    Joined:
    Sep 3, 2018
    Messages:
    6
    Balance:
    - 25Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    3DOF, DC motor, Arduino
    Thanks for fast reply. I downloaded 2.3.1 version and I saw rotational axis type. However it shows 180 degrees and I can not change it. Can I change it more than 180 degrees. My sim will be have aprox 360 degree of rotation. Now we are in POC stage.

    I hope I can post first pictures end of this month. But I can write down some features. 4 DOF simulator work with simtools. It will be commercial. near 360 degrees rotation /yaw, 58 degrees roll and pitch, 160mm heave, 440w BLDC motors for each axis.

    Thanks again.