1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

High Misalignment Spacers - Increasing Ball Joint Rotation

Discussion in 'DIY Motion Simulator Building Q&A / FAQ' started by boosted-lt1, Apr 22, 2015.

  1. boosted-lt1

    boosted-lt1 Member

    Joined:
    Jan 16, 2012
    Messages:
    32
    Location:
    Michigan, USA
    Balance:
    748Coins
    Ratings:
    +35 / 0 / -0
    My Motion Simulator:
    2DOF, JRK
    Just wanted to share something I found while researching parts needed to build my Connecting Rods which connect from the motor arm to the frame. I'm setting up my 2DOF project to max out the universal joint for pitch and roll which is just over 30 degrees in every direction. I was a little concerned that the 3/8" rod ends I was going to use from a go kart tierod would only rotate something like 15-17 degrees or so once you put washers or a spacer on each side (with big diameter washers even less) High Misalignment Spacers solve the issue by stepping down the inner diameter of the ball itself and allow part of the spacer to take the form of the outer diameter. These allow about 29 degrees of rotation according to the manufacturer (58 degrees total freedom) and can be inserted into any rod end of this type (they come in a lot of different sizes). Maybe this will help someone, it was new info for me!

    A comparison image and video below

    Comparison: http://www.kartek.com/Media/Images/Large/HiMisStandardDemo.jpg

    Attached Files:

    • Like Like x 3
    • Informative Informative x 3
  2. BondeX

    BondeX Active Member

    Joined:
    Feb 11, 2016
    Messages:
    141
    Occupation:
    EE
    Location:
    Michigan, USA
    Balance:
    1,515Coins
    Ratings:
    +76 / 0 / -0
    My Motion Simulator:
    2DOF, 3DOF, DC motor, Arduino, 6DOF
    Where do you buy all of this?
  3. Historiker

    Historiker Dramamine Adict Gold Contributor

    Joined:
    Dec 16, 2010
    Messages:
    2,158
    Occupation:
    Retired
    Location:
    Michigan USA
    Balance:
    9,176Coins
    Ratings:
    +2,156 / 19 / -1
    My Motion Simulator:
    3DOF, DC motor, Arduino, Motion platform, 6DOF
    Ebay is your friend :)

    Thanks for sharing this Scott. I missed it way back when you posted it. I was lifting walls and a roof then.
    • Like Like x 1
    • Agree Agree x 1
  4. That Dude There

    That Dude There Member

    Joined:
    Feb 19, 2017
    Messages:
    57
    Location:
    USA
    Balance:
    430Coins
    Ratings:
    +27 / 1 / -0
  5. mirkobastianini

    mirkobastianini Active Member

    Joined:
    Jan 23, 2017
    Messages:
    193
    Occupation:
    informatic
    Location:
    italy
    Balance:
    1,300Coins
    Ratings:
    +77 / 2 / -0
    My Motion Simulator:
    2DOF
    What is the right proportion to standard bolt size? I have M10 ball joint and I want to buy high misalignment spacers, but on ebay I find only size in ("). Thank you so much
    Mirko
  6. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,463
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    144,614Coins
    Ratings:
    +10,741 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    There are a number of approaches to spacers, that you can make or buy: https://www.xsimulator.net/community/faq/heim-rose-joint-conical-spacers.72/

    This should help if you want to find metric sizes on Ebay: https://www.ebay.com/sch/i.html?_od...0mm.TRS0&_nkw=rose+joint+SPACER+10mm&_sacat=0
  7. mirkobastianini

    mirkobastianini Active Member

    Joined:
    Jan 23, 2017
    Messages:
    193
    Occupation:
    informatic
    Location:
    italy
    Balance:
    1,300Coins
    Ratings:
    +77 / 2 / -0
    My Motion Simulator:
    2DOF
    Ok, I've talked with the owner of this site, and I've founded right things (for my case):

    -4 of this: http://www.mcgillmotorsport.com/m10-x-1-5mm-right-hand-female-sik10b-bronze-lined-rod-end-152/

    In my case I want to use M10 rod ends, but the hole for screw in my chair is M8, so I need to use this reducer:

    -http://www.mcgillmotorsport.com/m10-to-m8-rod-end-misalignment-reducers-pair-460/

    Anyway, I need to put this high misalignment on the lever near the motor right? So finally I need 8 of this component (one for each side of road end)?