1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules

Simulateur 3dof any mobile + wseat 2 ou 3dof

Discussion in 'DIY Motion Simulator Projects' started by zigzag49, Aug 25, 2016.

  1. zigzag49

    zigzag49 Active Member

    Joined:
    May 27, 2014
    Messages:
    251
    Balance:
    704Coins
    Ratings:
    +220 / 3 / -0
    My Motion Simulator:
    2DOF, Arduino
    A video of the simu, there is that roll pitch and heave, I wait for an order to continue on the seat.

    • Like Like x 1
    • Winner Winner x 1
  2. mariano68

    mariano68 Active Member

    Joined:
    Nov 15, 2014
    Messages:
    577
    Occupation:
    builder contractor
    Location:
    Argentina
    Balance:
    3,338Coins
    Ratings:
    +395 / 2 / -0
    My Motion Simulator:
    2DOF, Arduino, 4DOF
    I really like the responsiveness of the heave effect, I should have gone that way... :(
  3. zigzag49

    zigzag49 Active Member

    Joined:
    May 27, 2014
    Messages:
    251
    Balance:
    704Coins
    Ratings:
    +220 / 3 / -0
    My Motion Simulator:
    2DOF, Arduino
  4. zigzag49

    zigzag49 Active Member

    Joined:
    May 27, 2014
    Messages:
    251
    Balance:
    704Coins
    Ratings:
    +220 / 3 / -0
    My Motion Simulator:
    2DOF, Arduino
    [​IMG]

    Beginning of the prints for the linear guides, the rods and bearing make 16mm its will be used for the seating therefore the effect surge.
  5. zigzag49

    zigzag49 Active Member

    Joined:
    May 27, 2014
    Messages:
    251
    Balance:
    704Coins
    Ratings:
    +220 / 3 / -0
    My Motion Simulator:
    2DOF, Arduino
    Il me faudrai une plus grande table:grin

    I will need a larger table:grin
  6. zigzag49

    zigzag49 Active Member

    Joined:
    May 27, 2014
    Messages:
    251
    Balance:
    704Coins
    Ratings:
    +220 / 3 / -0
    My Motion Simulator:
    2DOF, Arduino
    Its continuous, fixing the bearings on a composite plate, like the one seen in public showers.
    [​IMG]

    Cutting the two flat iron that crossed the seat to leave room for the sliding tray.
    To see for the engine because it will be found under the plate.
    [​IMG]
    [​IMG]
    [​IMG]


    Sway sliding tray with backrest.
    J'ai doubler le bas du baquet de mousse pour avoir un meilleur appui au niveau des lombaires.
    [​IMG]

    Set of parts for linear guide.
    [​IMG]
    [​IMG]
    [​IMG]


    Continuation of the slide / back, remains to see or place the engine and can be added a curved form of each side pure to drive the bust.
    [​IMG]

    Cutting the plate for the passage of the crank, I have to make an extension so that the rod protrudes from the plate.
    [​IMG]
    Last edited: Mar 20, 2017