2 dof seat shaker build

Started on my sim. Still need so more parts but here's what I got so far.
1. 4 -EHCBS-6-01 Richco Edge Hold
2. Cable Matters 2-Pack, Gold Plated Hi-Speed USB 2.0 Type A to Mini-B Cable in Black 6 Feet
3. Cable Matters 2-Pack Heavy Duty Computer Monitor Power Cord in 6 Feet
4. 4 of QSC 1/2-3/8 High Misalignment Spacers, Rod End Spacers
5. 4 of QSC CMR-8, 1/2 X 1/2-20 Economy Male RH Rod End
6. 4 of QSC 1/2-20 RHJN, 1/2-20 Steel Right Hand Jam Nut, Clear Zinc Plated
7. 50mm Dia Universal Joint Threaded M8 x 46mm Furniture Glide Leveling Feet Pack of 4
8. 2 of Industrial Motion & Position Sensors 4.5 - 5.5 Volts Linearity +/-0.5% Hall Effect
9. XBRdepot 1 Pack of 4 Premium Self-Stick Aluminum Heatsinks for XBOX 360 RAM ANA and Southbridge Cooling (4 individual PCS)
10. White ABS IP65 Waterproof EnClosure Junction Box 200mmx155mmx80mm
11. Cooler Master SickleFlow 120 - Sleeve Bearing 120mm Blue LED Silent Fan
12. GEAR MOTOR 12 VOLT GREAT FOR SAWMILL/CRAB POT PULL/FEED 150/160 rpm 25:1 ratio
13. 10x 30cm 300MM Servo Extension Lead Wire Cable For Futaba JR
14. 2006 Ford 6.0 Powerstroke Drive shaft Flange u joint and section of tube
15. (Lot of 2) HP DL380 G4 Power Supply, DPS-600PB B, 575 Max Wattage, 338022-001

Still need to buy 2 jrk controllers, pc, video card and monitor

Started on the frame, mig crapped out on me, had to bring out the arc weilder. Hadn't done any real weilding since high school. I'm 41 now,lol. So this may get ugly.

When I installed the seat . I was way too high. I cut the u-joint shaft down to about 8". I took measurements off my pvc rig as I liked the way it sits. Installed motor brackets and arms. I'm thinking I going to redo the arms had to cut in half and reweild due to my seat being so high. They are not bent, just not perfectly straight from the heat from the wielder and being on the ground didn't help either. The arms bottom out about the 4:30 position on a clock is this ok? What I mean by bottom out is that the square tubing hits the lever and stops. Also I going to have to redo the steering wheel square tubing, its to hard to get in and out of it.

Got my jrk controllers in . have a question. Do I need to connect both pins on the jrk to the 5v ,and the ground and just one side that says feedback?

Just 1 Pin
I think 1 pin of 5v and ground and Feedback are for Potentiometer 1, and the others for Potentiometer 2

Looks good

Redid steering column so I could get in and out. Redid tie rods so they were straight. Added bracket for shifter . Hooked up jrks and pots. Cleaned up some of the wires .

Very good, this being excellente

Still waiting on my PC. Fedex lost the first one I ordered

Nice work so far, I hope you get the PC soon.

Got my PC in. Centered the pots. Read the quick start and the full simtools manual. Getting no movement when I go to the output teasting. Jrk"s are lit up green and yellow. Change coms from 3 to 4 and 5 to 6 , still a no go. Anybody see anything wrong? Pics of screens below. Sorry if grainy took with my phone. Manual said Microsoft Dot Net 4.0 is mandatory, I have Microsoft Dot Net 4.6.1 will that cause a problem?

I see com ports 3 and 4, but you used 3 and 5

did you set JRK utility?
Once you've done that you can then set Simtools, but first use the jrk utility to set max and min axis usage and PID.

EDIT: if you've already done that, post jrk utility pics

ok , i got it. Did't see that anywhere . Actually did a search for anything like that and didn't see anything. I just set the pots at center,didn't actually set them up. Thanks again Blame73 and noorbeast (the king or queen, which ever the case may be, of links)

that's right, you're are the king

always you can give us an explanation or advice

cheer up~!

Got back from a mini-vacation, started to tune simtools. Only reading sway and surge from output testing on tuning center. Thinking i need to invert some of the settings? Or it maybe something completely different. Read the FAQs many times, may be getting thing confused with oneanother ,set all forces to 20% , nothing except sway and surge.