1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

One Motor or Two

Discussion in 'DIY Motion Simulator Building Q&A / FAQ' started by terry wells, Apr 7, 2014.

Page 3 of 3
  1. testlab

    testlab New Member

    Joined:
    Jun 2, 2016
    Messages:
    8
    Balance:
    33Coins
    Ratings:
    +2 / 0 / -0
    My Motion Simulator:
    2DOF, Arduino, Motion platform
    Добрый день. Я использую схему модe2 . После прошивки , никакой реакции. Должен ли реагировать мотор с этой прошивкой на положение резистора?
    _____________________________________________________________________________________________________________________________
    Good afternoon. I use the scheme mode2. After flashing, no reaction. Should the engine to respond to this firmware to the position of the resistor?
    testlab, Sep 20, 2016
    #41
  2. masterhoo

    masterhoo New Member

    Joined:
    May 20, 2017
    Messages:
    25
    Location:
    Peru
    Balance:
    370Coins
    Ratings:
    +2 / 0 / -0
    My Motion Simulator:
    2DOF, DC motor, Arduino, Motion platform
    @bsft, so in other words if I find 24V motors only, what type of motor drivers would be recommended? The Sparkfun Monster allows 16v max.
    masterhoo, Jun 22, 2017
    #42
  3. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    20,535
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    145,034Coins
    Ratings:
    +10,776 / 52 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    You could use a Sabertooth to drive both motors, see the FAQs for code and wiring details.
    • Like Like x 1
    noorbeast, Jun 22, 2017
    #43
  4. Krisie300

    Krisie300 Student Engineering

    Joined:
    Jan 18, 2016
    Messages:
    11
    Location:
    Netherlands
    Balance:
    146Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    2DOF, DC motor, Arduino
    Hi! I think I have a problem with the motors, cause the buzzer of the multimeter makes noise!
    So I've opened the motor but I can't see where it is attached to the body of the motor. The problem is that the motors don't turn in full speed backwards and when I put it in backwards the motor just stops turning after a little while. So here are a couple of photo's and a video.
    Hope someone can help me!

    Attached Files:

    Krisie300, Nov 2, 2017
    #44
Page 3 of 3